GRAPHIC KIT FOR KLX 250 - Metal Mulisha ~ TRIPLE-X

Sabtu, 15 Oktober 2011

GRAPHIC KIT FOR KLX 250 - Metal Mulisha

01.13

Mahda Askia

No comments

Our KLX 20 Graphics are thick as well as UV protected, scratch resistant over-laminate that holds up against harsh riding conditions. Includes custom shaped pieces for the tank and/or shrouds, front fender tip, rear fender, fork guards, air box and swingarm decals. Printed on high-performance vinyl with aggressive adhesive specially designed for KLX 250 plastics. A very affordable option for customizing your bike to the extreme.

Posted in: Nyayu Mahda Askia

0 komentar:

Posting Komentar

HOW TO INSTALLING GRAPHIC KIT

First. Provide the tools he needs it: - Cloth Wipe Clean, smooth and soft cloth, and coarse (type catton better) Clean Water Shampoo Eucalyptus oil Hair Dryer Straighten Tool / Penyerut Water (usually to clean his glass) / ID cardbekas Second. Clean the cover-cover motor body in advance .. Use a landline and clean water, rinse with water when it is. Ensure clean and no dirt / mud that sticks. Use eucalyptus oil to remove stains that can not lose with soap, such as glue left over from the previous sticker marks / additional sticker (sticker cutting, etc.). If Yes, Clean again with soap and water. * Do not do it in a place exposed to direct sunlight and areas that are dusty / windy and dusty. Third This step is a step to start the installation sticker .. Spray the water is mixed with a shampoo, a ratio of 5:1 / 5 liters of water with a sachet of shampoo. Shampoo + water spray until smooth / flush until blended. Use a shampoo that had a low Ph Balance ... (Based on experience .. Balance Ph High will be a little disturbing nature of the adhesive (glue) on the sticker ... aka trap rather difficult to stick) Fourth Select and make sure the Sitcker / Decal as intended or in accordance with the cover body. Peel the backing (lining the back of the sticker / protective adhesive), then spray a mixture of water + shampoo on the adhesivenya, until blended. Make sure the hand / fingers are clean or free of things that can interfere with (dust, dirty, or beroli) Fifth. Save / Put the sticker / decal that was in the wet the backing (adhesive him) on the cover body. But first make sure the cover body is still wet and seemingly flat by liquid water and shampoo. The use of liquid water and shampoo before, the point is that the sticker / decal is not directly attached to the cover body, and can be shifted to the right-shift, and as you wish. So Slide-slide sticker that had been stored above the cover body to fit and appropriate. Sixth. Do not wait too long, Take water penyerut appliance / secondhand IDcard / SIM .... make sure the surface is flat and pliable .. Previous spray the surface of the sticker at the top with water / liquid mixture. Its function is to learn later that we menyerut water in the surface / decal sticker (adhesive backing) .. sticker with a picture of the upper surface and laminated not damaged / scratchy ... Sort of the most prominent and first rate massage .. do not force the water in the contract,, Usahankan massaging water to one side only .. and navigate to the outside of the cover body ... Do not press tools press penyerut water too .. give light pressure are important water section sticker backing out Seventh. After a flat first section penyerutan dahuli finished in doing, then it will look like on the picture to Step 7. That part will appear shrunken, wavy, stiff, uneven and not follow the contours of the body cover. Do pasakan menyerut / leveling in the area with penyerut / IDCard. Let it first. Eighth Use a Hair Dryer at this step. Hair Dryer serves to help shape the contours of the sticker / decal to conform to the shape of the cover body. Jgn use a hot gun / hot water when not used. Keep your distance Hair Dryer bursts of heat with a sticker / decal. Approximately 15cm. A blast of heat from a hair dryer to the sticker that rigid and unwilling to follow kontur/lekukan2 of the cover body. Jgan too long. Only sometime after, just after aja .. Sticker that is rigid and does not stick to the cover body would appear as though shrinking and follow the contours of the body cover ... Set Level Air Flow / Temp on hair dyer in the medium level. Do the right hair dryer for too long on a sticker / decal. Because it will make it mushy and stickers will damage the backing layer (adhesive).

TRIPLE-X

Sabtu, 15 Oktober 2011